Watering your Foundation – Its a Texas Thing Part III

March 23, 2016

Texas-Drought-2011As mentioned in my last post on watering your foundation; Here in North Texas it is essential.  Since this is not a one time event but a regular requirement, you might as well look at a relative permanent approach to the solution. I identified several ways to do this in my last posts on the subject but I wanted to share a bit more permanent method. The concept is the same, but its a bit more work, and you may want to hire an irrigation specialist to do it.

The biggest difference in this solution is capitalizing on the fact that you may already have a permanent in-ground sprinkler system. With this system, you operate it as any other section to your irrigation system profile and its no longer a separate system to take care of.

Criteria of existing lawn sprinkler system: For this to work, you need an automatic lawn sprinkler system and a couple more conditions to make it work.

  1. sprinkler controllerElectronic Irrigation controller: The irrigation controller will be the source of the schedule to water the foundation.
    1. Spare Zone: Most controllers come in 4, 6, 8, 12 (and so on) zones. You will need at least one vacant zone position for this to work. You can query the controller by stepping through the zones. When you select the zone with the controller, look for statements in the readout that could say things like; vacant, not-wired, turned off, etc. It that doesn’t work, open the back half of the controller and look at the incoming wiring. Each position that has a number on it represents a zone. If you find a number with no wire, you should have a vacant zone. If you don’t have any vacant zones, your forward path from this point would be to replace the controller with more zones. This may exceed your budgetary limitations
    2. Spare Wire: In many cases during the initial installation, the cable with the zone wires in it, may exceed the number of connected zones. So look for some coiled up wires in the base of the controller.  If that is the case, you are in luck and can use one of the spare wires. If you have no spare wires but a spare zone on the controller, you would have to add a pair for the new zone. (a colored wire and a common (white) wire).
  2. sprinkler-valveAdding a New Valve: At this point, you have a 1)zone position in the controller, 2) a spare wire for the new zone. Now, locate all the existing valves in the yard. Specifically ones that are close to the house.
    1. In that valve box, look for the same color wire you identified in the controller, if it is not there, check the other valves. Worst case, you may have to bring a new wire to your chosen location.
    2. Dig up around the existing valve and identify which pipe is under pressure all the time. Once identified, turn the main water supply off that feeds the sprinkler system (probably near the water meter), you will cut into the pipe and add a new valve. You may have to run a short piece of wire from the existing valve to the new one to hook it up. The connection will be one colored wire and one “Common”.
    3. When you buy the new valve, make sure it has (low) flow control, and or is designed to work with zones that don’t use a lot of water pressure. The drip lines you use have a low GPM (gallon per minute) rating as well as low pressure.
  3.  Polypipe: Depending on where you locate the new valve, you may need a section of polypipe to get you to the foundation.  You can cut the hose to length and use the polypipe fittings to make up the ends. Make sure the polypipe and fittings are the same dimensions. Since all these connections are on the low pressure side of the system, these fittings are just simple resistance (chinese finger) snap in connectors.
  4. Drip Lines:  From the poly pipe, use the same fitting to transition to the Drip Line. These hoses are designed with drip emitters in the hose every 12 inches.  Run it around the house keeping it about 6 inches from the foundation.  You can bury them a couple of inches or hide them with mulch. Staking them with landscape stakes will help keep them in place as this product does not like to lay flat to the ground. You can purchase the hose in bulk from the Orange Box store of Sprinkler Warehouse. You will need to also purchase inter-hose connectors as well as a way to connect to your water. If you have to make a sharp turn it is better to use a fitting than bending the pipe. You do not want to crimp the hose. Splitting the line with a Tee is totally acceptable, and it will also allow a little better flow control if the go half way around the house with one feed and half with the other.

 

So here is what it looks like in dollars. Admittedly, you can probably do this a little cheaper, but I used high quality components, so this should last for years to come.

DripSys for house

Related articles:https://homeownerbob.wordpress.com/2012/03/05/watering-your-foundation-its-a-texas-thing/

https://homeownerbob.wordpress.com/2012/06/06/watering-your-foundation-getting-ready-for-the-summer/