Watering Your Foundation – A Permanent Solution

October 13, 2017

Several months back I wrote a post about Watering Your Foundation, after that I wrote  Watering Your Foundation – Getting Ready for Summer and in that post I promised a final follow-up on creating a permanent solution to creating a low maintenance solution that removes most of the problems associated with earlier solutions. Granted, this one is a bit more work and on a DIY scale of 1-10 10 being the hardest, I would give this a 7-8 (depending on what you may or may not already have. Since you have already read the last two, no need to go through the why and what for, but to just pick it up from the last post. Since the summer is (mostly) over, this might be a good project to complete with the weather is still pleasant.

The biggest advantages to this solution vs. the last one is, convenience, and integration into a lawn sprinkler system.

Things you will need to for this to work with the least amount of inconvenience and disruption. This solution is based on having all three of the listed conditions. However, any of these items can be added, but it can dramatically impact the cost to provide it.

  1. Preexisting  lawn sprinkler system in good working order and a timer/controller
  2. The timer/controller will need to have at least one extra or vacant station assignment. If you have more station numbers than active stations you probably have an extra one.
  3. You will need to determine if you have a spare controller wire (in the controller) and you will have to locate that same wire outside.

The next step is to create a new zone or station on your lawn sprinkler system.  I will cover the basic process but if you have never really cut into your system, this might be the time to get some knowledgeable help or hire a sprinkler contractor to build you a new zone.

Create a New Sprinkler Zone

  1. Find a sprinkler zone  that has its control valve close to the house.
  2. Dig up the dirt around the control valve enough to expose the control valve and the associated water pipe that feeds the valve. Figure out which side of the valve has pressure on it (all the time).
  3. Determine that the spare wire you located in the timer/controller shows up here too! Us a volt ohm meter as a continuity tester to confirm.
  4. The pipe feeding the valve is under pressure, so you will need to turn the water off at the source before you do it.
  5. To determine which is the pressure side, there should be an arrow, or water flow indicator on the valve body.
  6. .Cut the pipe, Tee in a joint  to install a new valve.
  7. Install a drip zone flow control valve equipped with a filter assembly. This valve will keep the flow in spec as well as keep the emitter from getting stopped up.
  8. Extend a wire from the existing valve to the new valve including a common (usually white) and a new wire that you are picking up from the controller timer.
  9. Make sure the new valve is closed and turn the water back on and check for leaks.
  10. If you want to test it at this point, go right ahead, but realize if you did this correctly, it’s gonna get real muddy real quick.

Parts Needed for the Drip Emitter Foundation Watering System

  1. 1/2 poly hose to use for areas that do not need the emmiters
  2. 1/2 Emitter tube, used to circle the house
  3. Various connector/fittings. You will need some fitting to go around tight corners since the pipe does not make sharp corners as well as connecting to the valve.
  4. Landscape anchor staples; use to pin the tubing down in place while you are installing it.

Install the  System

  1. Dig a ditch from the new valve to about 12-16 inches from the foundation to conceal the feeder pipe so it will not be exposed to damage in the yard.
  2. Depth of new emitter hose is kind of “it depends”, so in other words, it can be on the surface or 3-12 inches below the surface. Either way, realize that when gardening or digging around the flower beds, if you hit the emitter pipe, you can easily cut it. So regardless of the depth, after gardening, run the section to identify any leaks.
  3.  Since you are probably 10 or more feet from the house, you may want to use 1/2 poly hose from the valve to the house foundation (unless the valve is already at the foundation, then you can just start with emitter hose). You can buy shorter lengths of this from the big box store, but depending on your house arrangement, you may want to use this pipe in places you do not need to water
  4. Connect the emitter tube and route through the landscape staying about 12″ from the edge of the foundation. This tubing is sort of stiff, so use a connector to make a sharp bend. Use the landscape staples to keep it in its place.
  5. There are no rules to stop you from installing a Tee and going both ways around the house, and if you have to branch out, that is fine too. 100 feet is the limitation of the emitter tube from the valve, but you can tee it in to two 100 ft lengths.
  6. Make the electrical connection at the sprinkler controller and program in the new zone. You can have a summer and winter time schedule, but its good to water this zone all year long, again to keep the soil close to a constant moisture level.

 

 

Advertisements

Seasonal Reminder – Lawn Sprinker Tuneup

April 5, 2016

If you are a follower of this blog, lawn sprinklers seems to be a regular topic. I get more hits on this one subject than all the rest. After reviewing  the current articles I found that I lacked a straight up, “seasonal tune up” article. So, for this weeks post I am going to walk through a methodical process of checking your sprinkler system. Generally speaking this is about a system that is designed correctly and  working properly.  I typically do this at the beginning of the watering season then again in mid-summer.

Material/Tools Needed:

  1. Spare sprinkler bodies: You should normally keep some extra sprinkler bodies that resemble the product that was installed with your system. Having identical sprinkler bodies will keep replacement and repairs simple.
  2. A handful of various sprinkler nozzles: Even though there may be several types of sprinkler heads (pop up, rotary or impact), it is important to have extra copies of the same nozzle that are being used in the various zones. Even though many home centers prefer to sell you the sprinkler body with the nozzle, having them as separate items will save you time and money.
  3.  Sharpshooter Shovel:  This particular shovel works well when working on sprinklers as you can dig around a sprinkler without disturbing too much dirt. Dirt and dirty water  is the enemy when it comes to working on sprinkler systems.
  4.  Sprinkler flags: You will probably have to buy these in a pack of 100, but it will be less than $10. You will use these to mark sprinkler heads that require attention.
  5. Screwdrivers: 1 small screw driver, 1 medium screw driver (flat and Phillips head style). These will be used to disassemble nozzles and some heads.
  6. Dental tool: Something like this link will work; these can also be found at the Orange Box store. It is very common for sprinkler nozzles to capture small pebbles that will lodge in the nozzle disrupting the sprinkler spray pattern. You will want to pick out the debris without damaging the plastic.
  7. 1 pair of medium-sized Channel Lock pliers: These can be used to adjust, tighten and loosen the body of the sprinkler head especially if your hands are wet.
  8. 1 pair of medium-sized vise grips: Used as a way to extract nozzles from pop-up heads by lightly holding the nozzle riser exposed. Never use a lot of pressure as you can easily damage the sprinkler head.
  9. WD 40 Lubricant Spray: Used to lubricate various parts that are supposed to move or react to the water pressure. WD40 is a fish oil based product and should not damage the grass.

SPRINKLER TESTING PROCEDURE:

  1. Activate the test sequence in the Sprinkler Controller: Most controllers have a test function that allows you to run the system in short intervals. If you can choose the time limit, set it to two minutes. If your controller does not have this function, you can have a friend turn the sections on one by one. TIP: If you have to do this manually, find some walkie-talkies to communicate with your partner.
  2. Find the first zone that is running:  Carrying your sprinkler flags, walk around and through the zone that is running, looking for the six items mentioned below. Use the flag to identify problems. However, try to realign the heads in this first sequence while the zone is running. Use the Channel Lock to grab the body to make adjustments.
  3. Repeat #2 for all the zones: I find the sprinkler flags really help, cause you can go directly back to each problem once you have made it through the entire system.
  4. Repair, replace  or adjust the heads as required: One of the most  important elements of sprinkler repair is to avoid introducing dirty water into the system. The dirt will make its way to all the downstream head and clog them up. If you find a broken head or pipe within your inspection, you may have to clean all the nozzles (see #2 below) in that zone.
  5. Run the test sequence again: As a final step, run the system one last time to ensure that everything is operating to your expectations.

Common Problems and Solutions:

  1. Misaligned Heads: Heads that are used around the perimeter of a property typically use patterns less than “full circle”. These heads will require occasional realignment to keep them from spraying on a sidewalk, fence or house. You can  adjust  either the nozzle, neck or sprinkler body. Try adjusting to the right (righty tighty, lefty loosie). If you have to turn it to the left, try not to turn it more than a 1/4 or 1/2 turn. Turning the head too much to the left may cause the nozzle or head to disconnect itself (while under pressure), this may cause a guiser of water and will get you real wet.
  2. Dirty Nozzles:  If the pattern seems uneven or broken up. The nozzle is dirty. With the water off, grab the sprinkler stem and raise it as if it were spraying water. Use your vise grips to LIGHTLY hold the stem up. Remove the nozzle and pull the filter (with the dental tool or your finger tip). Blow through the filter and nozzle. If this doesn’t remove all the debris, use the dental tools or water to clean further. You may have to disassemble the nozzle completely to get the dirt out. If the filter was completely stopped up, turn the sprinkler zone on/off very quickly to flush the line at this point (with the vice grips in place). Reassemble the nozzle to the head and release the vise grips to let the stem return to the body. NOTE: The purpose of keeping the stem extended through this process is to avoid the opportunity for dirty water to enter the system.  
  3. Broken/Damaged  head: Besides the nozzle mentioned above, the sprinkler body can leak as well. This could be out the bottom, side or top. Sometime the heads can be rebuilt, but at this stage its best to just swap out the head with an identical body and nozzle. If it’s not muddy around the head, attempt to unscrew the complete body out of the ground. Without disturbing the dirt, re-insert the replacement head. If you have to dig it up, use the sharp shooter shovel to expose the  head down to where it connects to the next pipe. It’s best to dig the hole a bit deeper than the head. If water comes out, you do not want the dirty water to reenter the system as mentioned above.  Replace the head and the surrounding dirt.  This sprinkler repair  link has a video included that might be of help.
  4. Sprinkler heads do not recess into the ground after spraying: This is a very common occurrence caused by small dirt particles surrounding the elevated riser at the wiper seal of the sprinkler head after the water is turned off. Grab the head by the tip and spray WD-40 on the riser. Work the shaft until it moves freely. If that doesn’t clear it, replace the head  and rebuild the old one in the sink to get all the dirt out of it.
  5.  Heavy Running or Pooling Water: This could be associated with #3 or it could be a damaged pipe.  With your shovel, LIGHTLY remove the wet dirt, you do not want to cause anymore damage. Dig below the pipe or area to be repaired. Use a coffee can to remove as much of the water and dirt as possible. Make the repair as necessary.
  6. Weeping heads:  Occurs when system is off. Typically you will notice this on days the sprinklers are not running, or you find constant moist spots. Typically, you must disassemble the sprinkler valve and clean it.  Rebuilding the valve may be required as well.
  7. Draining sprinkler head: similar to #6, but usually happens with a head that is located lower that other heads in the zone. This is fairly normal and can be left alone. If it happens in a bad spot and you really don’t like it, you can add a lateral line drain to disperse the water.

 For more detailed information, take a look at these other articles I have written on the subject: Lawn Sprinkler Efficiency Part II, Lawn Sprinkler Efficiency Part I ,  Searching for Lawn Sprinkler Valves, Chasing Lawn Sprinkler Leaks; Finding Sprinkler Valves and Common Problems,Lawn Sprinkler Efficiency Upgrades Part II,  .



Chasing Lawn Sprinkler Leaks II

July 31, 2013

lawn20edge20pop20up2011My wife complained the water bill had gone to the moon (again) last month. Even HomeownerBOB has sprinkler leaks!! In this post I hope to show another way to identifiy water leaks in automatic lawn sprinklers. After doing the basics, it was obvious, it would take a little more effort.

At this point, I still had no idea where the leak was other than I was confident it was past the valve as the meter was not moving otherwise.

Most sections should use near the same amount of water except where it might be a very small section or (in my case) I have 3 sections using emitter tube for drip irrigation, but even in this case there should be some relative similarities.

  1. Access the water meter for the property, clean the meter face or get to where you can watch the meter move.
  2. Make sure all other water devices are turned off or wont come on during this test
  3. If you have a controller that has a test sequence, set it to 1 minute. If not, have some one manually operate it at one minute per section.
  4. Have a friend turn it on while you are positioned to watch the meter
  5. Once it starts, watch the meter (this is not real scientific, but you are looking for a difference in the trend.
  6. You should beable to recognize when the watering changes from one zone to the next as the water meter will stop (very briefly) then start again.
  7. In most cases the meter will briefly run very fast, then (noticeably) slow down.
  8. Compare the speed and gallons used by each section. (your comparison should be like for like, in other words, pop-up sections to pop-up sections and so on.
  9. If you find a section that does not trend the same way (i.e. does not slow down after the initial turn up), it is likely that this is your problem zone. In my case, I had two that looked funny.
  10. Stop the test and run just the sections that appeared perculiar. Walk the entire section, head by head to find larger quantities of water.

100_0203In my case, the problem was in the emitter section. It is not unusual to spring a leak in these sections either due to driving a shovel (my wife) through one, or one of the ends coming open. It ended up being neither, but was caused by an inline filter I installed (below ground under this cover) to keep the emitters clean. This has happened to me before on a different section as I used these fancy filters that self clean them selves, unfortuntly they tend to stick open, and they have to be replaced. I replaced them with a non-self cleaning type. I have one more that could go bad, so its only a mater of time.

Make sure and click on the Lawn Sprinkler tab to see all my articles on lawn sprinklers.


Finding a Lost Sprinkler Head

July 18, 2009

Lawn Sprinkler4Finding a lost sprinkler head can be a challenge, simple in concept but difficult if you don’t have a plan.  Sprinkler heads can fail to rise to the occasion when under pressure. The longer they fail to operate the harder they may be to find. 

Perform these items first:

  1. If available, look at the drawing used during the installation system, it may work as a road map in identify the general location.
  2. Look for an obvious brown/dry spot. Run the sprinkler, it may pop up but be clogged. If so, disassemble it, clean it, reassemble it, install it and you are done. If not, go to #3.
  3. If the entire zone appears to be weak, you may find water pooling. This could actually be a broken head or pipe as in this condition you are consuming way more water than the design.
  4. With the sprinklers running, look for mushy ground  and water pooling. The head may be working, but it is too covered up to rise above the grass. Use a shovel to work the dirt (carefully). It may pop up once the dirt around it has been loosened up.

Missing SprinklerOkay, that was the easy stuff, now it gets hard. Go to the Orange Box store and purchase some sprinkler flags. Place a flag at each known head. Measure the distances between the heads as shown in the drawing.  You should find an area that does not measure (in relative terms) like the other ones. Start poking around with a shovel (carefully) in an attempt to expose the head 

Still no luck? Using the same method described in Finding Leaks in Sprinkler Zones and Common Leaks. You will need to turn off all the heads in that zone. Let the water run, hopefully,  it will show up since you are concentrating all the pressure to the missing head. Check your meter and look for moderate movement in the meter. If you have no movement in the meter the sprinkler head could be capped or not there at all.

Still didn’t find it?  You may not have a head there at all and the design just did not cover it well. So you may consider adding a head if the zone can accommodate the additional water use.

You may also take a look at one of my other articles for help in the Lawn Sprinkler catagory.


Lawn Sprinkler Nozzles, Can Changing Them Make a Difference?

July 12, 2009

sprinklers-01   

Heavy misting of the sprinkler heads can result in as much as a 25% loss in water.    

New sprinkler heads and nozzles coming on the market are claiming sizable water savings, but how much water can you really save (if any)?  Stream sprayers are normally found only in orbital or rotary heads and are typically found in larger landscaped areas and can be spaced 20′ to 30′ apart. With an open landscape, these heads can water more ground with less water. Up until now, there have been few options for smaller residential properties other than traditional pop-up heads using spray type nozzles. Spray nozzles are designed for spacing limitation from 8′ to 15′ and as with any type water sprayer, there is a correlation between distance and trajectory or arc necessary to obtain the distance. The greater the distance, the greater the height of the arc to obtain the distance. Greater distance = greater misting.    

But trajectory alone is not the only culprit to misting. High winds, high pressure, evaporation and excessive overspray all contribute to the water loss factor associated with misting. This misting can account for a loss of 10-25%. It’s this misting factor (more characteristic of spray nozzles over stream nozzles) that contributes to a lower efficiency found with the spray nozzle.  And its the low misting factor found with the stream sprayer that makes for an attractive alternative.     

In an attempt to make automatic sprinkler systems more efficient, some manufacturers have created a stream type nozzle designed as a direct replacements for the standard spray nozzle (aka pop-up sprayer). If you have read my earlier posts on lawn sprinklers you know that pop-up type spray heads can lose 10% or more of their water spray to the wind and evaporation.   Before we look at the differences between spray nozzles and stream nozzles, lets consider the ways to reduce sprinkler misting. Some of these items can be readily addressed, some are design considerations.    

Standard Spray Nozzles: Standard spray nozzles atomize the water to equally spray or spread the water out in an even flow throughout their spray pattern. They are great choice for small residential properties as they provide good water distribution in a reasonable amount of time. Additionally they have many different nozzles to fit the various application requirements.   

012106_lwn_sprinkler02_dt   

  1. To much pressure: Optimally pop-up sprayers work best at 30 psi. High pressure can cause excessive misting.  TIP: To test the zone water pressure, you have to remove a head, replace it with a riser and thread on a water pressure gauge, then run the zone and check the pressure while the zone is spraying water.
  2. Don’t water during high winds:   This can be managed manually or you can add a wind anemometer to your sprinkler controller that will shut down the system at certain wind speeds. Even though we typically water in the night-time hours (to avoid excessive evaporation), windy conditions are as common during the night-time as during the day.
  3. Keep water spray output close to the ground: This can be achieved by designing a system where the heads are closer (such as 10′ apart compared to 15′ apart)  Spray nozzles with shorter patterns use lower trajectories, will atomize the water less and have less distance to fall to the ground.  This item has to be addressed during the initial design as shortening patterns in an existing system could be considered a “do over”. I designed and installed my current system prior to stream sprayers, I took this approach by using 10′ radii heads. The water stays very close to the ground when the system is running. Granted, it caused me to use a lot more heads and zones. If I were to tackle it today, the stream sprayers would not only impact my water  usage, but cut back on material and zones installed. 
  4. Deliver the water in streams not in a spray or mist: The more you atomize the water, the lighter it becomes, allowing the wind to cause the water to drift away and evaporate before it has time to absorb into the ground or plant material.
  5. Deliver water directly to the roots through drip irrigation.  Flower beds can be easily converted (assuming your sprinkler system has specific zones for flower beds). For grass and turf this is a bit more involved but plausible.  In my current system I created specific zones for the parkway and driveway. Using direct bury drip lines, I am able to keep the turf green with virtually no run off. This is another condition that would need to be addressed in the original design.
  6. Refer to the  Alliance of Water Efficiency, for additional water saving tips. 

Water Use and Abuse   

There is a fine line between efficient water delivery and adequate water coverage. Many irrigators will “over cover” an installation to ensure all the grounds receive adequate water. The Irrigator wants to over-saturate the turf to avoid brown spots or low coverage areas, as making a re-trip to install additional heads can be costly. Creating a system that uses excessive water will cause them less problems in the long run. But in doing so, there may be a high degree of waste associated with the design. Don’t get me wrong, the lawn sprinkler business is very competitive and most people won’t spend the money to get a system with high-efficiency. Since water is still cheap and fairly plentiful this methodology will be with us for a while. However, the purpose of this article is to attempt to make your existing system more efficient and if you have a decent design, you can make some reasonable changes that will not terribly affect the performance of the system.   

Lawn%20edge%20pop%20up%201Stream Sprayers: Stream spray nozzles provides multiple streams from the nozzle in the defined pattern (90, 180, 360 degree pattern). To provide adequate coverage, the streams spray in a rotation throughout the pattern.  The beauty of the stream type nozzle over the spray nozzle is it will project water similar distances without high levels of misting. However, based on their delivery you may actually have to run the systems longer to get similar watering results, but since they are more efficient, it will not negatively impact the system performance.  With the move toward greater efficiency, the stream principle has been introduced to traditional pop-up sprayer. Some manufacturers provide them as replacement nozzles, where others require you to change out the complete head. TIP: Look at one of your spray heads to determine the brand, go online to see if the manufacturer makes a replacement nozzle, don’t be surprised if your local orange box store does not carry them. I have used Sprinkler Warehouse for many of my sprinkler parts and speciality items.   

The Test Case: I created a model zone with 4 heads, 2-180 degree heads and 2-360 degree heads.  I used the Toro 570 model body as it can be equipped with either the spray nozzle  or retrofitted with the stream nozzle. Optimally, the comparison is based on a 30 psi rating at the head.    

In converting the system from spray to stream we need to match the pattern as close as possible. Since spray heads are a mature product, many patterns and styles are available, but with the stream nozzles, the available styles are still limited. With the Toro brand, the new stream nozzles are not a direct comparison in spray distances and the stream nozzles may have to be tuned to reduce the pattern to avoid excessive over-spray onto the sidewalk. But they were pretty close.   

Stream Spray Matrix

Spray Nozzles De-rated by 10%

   

Sprinkler Table2

Spray Nozzles De-rated by 25%%

   

 From a cost comparison, it is beneficial to be able to re-use your existing spray heads if at all possible,  as having to buy new heads as well as the nozzles will add up quickly. When you look at the water saved vs. the cost of the change, it did not prove out (for me) since water is still very cheap. However many municipalities tack on additional charges based on water usage, so it could make a difference for you. If you are interested in seeing how much difference it makes, take the water saved (listed in the table and calculate it against your dollar per gallon charges found on your water bill.   

Based on the results of the chart, here is my observations using the 10% de-ration chart.   

  1. It requires 86.72 minutes using the stream spray nozzles to provide the same precipitation value as the spray nozzle provides in 60 minutes.
  2. Even though it requires 26.72 minutes more, the stream sprayers use 393 less gallons
  3. Factoring in a 10% misting factor, the stream sprayers use 5.77% less water or 471.63 gallons of water per month.

At a 25% deration the numbers are a bit more dramatic as you could save over 1700 gallons of water per month.   

Conclusion:    

  • Consider using the stream sprayers in a new design as you can use less heads, less zones, less pipe, less fittings as well as less water. 
  • Convert existing sprinkler zones to stream sprays where high wind is normal or misting is excessive.

Recommendation: If you choose to replace your existing nozzles/heads, change one zone at a time. Let it run through part of the season, compare the results by looking at your turf . For proper watering don’t mix spray nozzles with the stream nozzles in the same zone. To obtain an adequate amount of water similar to the spray nozzles zones, the watering time may have to be increased on the stream nozzle section.   

To see the entire series of lawn sprinkler articles go to Lawn Sprinkler tab on the HomeownerBOB web page.   

Good Luck   


Finding Leaks in Sprinkler Zones and Common Problems

June 13, 2009

bad sprinklerRecognizing a water leaks within a sprinkler zone can be  difficult as they may not reveal their location until  under pressure.

How do  you recognize a minor leak  in the sprinkler zone if it’s not obvious?

  1. The first noticeable trait would be the zone does not appear to cover the ground as well as it used to. You may also recognize plant material or turf that appears dry or starving for water.
  2. Moist mucky dirt, soggy spongy area(s) in the yard. Someplace that never seems to be dry.
  3. New or additional brown patches  in the turf indicating low water coverage.

If you have read any of my sprinkler articles you know that most sprinkler problems are with heads and valves. Both provide obvious indicators of water loss. Here is a recap of the most common problems: 

  1. Weeping heads: A slight amount of water is passing through the valve when it should be closed. The sprinkler heads remain wet well after the sprinklers have run. Typically, disassembling the valve and cleaning will correct it.
  2. Dirty heads: Dirt, pebbles and grunge can lodge itself in the sprinkler nozzle as well as the body and shaft of the sprinkler head. These problems will modifiy the pattern, providing excessive water in the wrong places. Start by replacing or disassembling the head and cleaning it.  TIP: Like for like heads and nozzles will reduce complications in future repairs. When a sprinkler zone is turned off,  typically the lowest head in the zone becomes the relief valve causing water left in the lines to drain out. This is very normal. However, in doing so, a suction is created that can pull in surface water, and dirt from around the other heads. This dirt can migrate throughout the zone clogging the other heads. TIP: If the location of the low head is in a bad place, an in-line drain can be installed in the pipe, but you will have to dig up the pipe to do it.
  3. Broken head: Obvious water spray outside the defined pattern. This can be corrected by replacing the head or the broken parts.  TIP: Keep extra sprinkler heads to replace bad ones. Rebuild the old ones if you can. Remember to reuse or replace the nozzle like for like. Many times you can replace the entire head without disturbing the surrounding dirt. This reduces the opportunity of allowing new dirt into the system and keep you from having to to dig the head up. 
  4. Lawn butchers: Weed Eaters and edgers are the death of lawn sprinklers. They can easily destroy several heads over a season of mowing.
  5. Allowing dirt in the system: No different than the water system in your house, allowing dirt in the pipes creates opportunities to clog valves and heads, creating more work for you. When working on sprinkler heads and valves avoid this by taking the appropriate steps  to stop surface water back into the system. When you run a zone and identify a head that needs attention, removing the head may create a suction that will pull water and dirt into the pipes. Admittedly more work, by digging up the dirt from around the head and getting the hole deeper than the head connection can reduce the opportunitiy of allowing dirty water into the sprinkler system. TIP: If there is no standing water at the head, attempt to change it without digging it up as described in number #3, this will save you some time.

If you have corrected the problems associated with the above list and you still have problems, its time to look deeper into the system. Most likely, if you have gone this far you are recognizing that a specific zone does not present the same pressure, or cover its area as well as the others.  This trait is an indication of a pipe, joint or fitting leak, and the leak is large enough to reduce the zone pressure but not enough to create a pool or hole in the lawn. 

water poolTry this method to further isolate the leak:

  1. Assuming you have pop-up type heads, adjust the screw on the top of the nozzle  (on every head in the active zone)  to shut off the water on that head(s) TOTALLY. This increased pressure may be enough to cause the small leak to burst. Continue to walk the sprinkler zone looking for mushy ground and water pools.  Also, go look at your water meter for measured water usage.  Look for the meter to be moving at a medium to  rapid pace (make sure everything in the house is turned off). TIP: Since lawn sprinkler heads are not rated to hold full pressure like a faucet, some small degree of water oozing is acceptable.
  2. If you have other styles of heads or #1 didn’t find it, this step #2 will be dirty wet work.  Conceptually, it’s the same as #1 but requires you to expose each and every head on the zone and install a threaded cap to replace each sprinkler. In this method, you have  to remove all the heads from the equation and the zone should hold pressure just like any pressurized plumbing line. Check the water meter; if you still see a water loss, leave the zone on for 2 or 3 hours, or even the whole day. Again, look for water pools or mushy ground and check your meter.

You may also find benefit in reading the other articles I have written on the subject: Lawn Sprinkler Efficiency Part II, Lawn Sprinkler Efficiency Part I ,  Searching for Lawn Sprinkler Valves, Chasing Lawn Sprinkler Leaks


Searching for Lawn Sprinkler Valves

April 10, 2009

sprinkler-valveFinding the lawn sprinkler valves can be challenging  without the correct tool. Most irrigators have a tool called a cable hound or cable locator. Think of this exercise as an Easter Egg Hunt and the valve is the candy.

Within all Lawn Sprinkler systems they are broken into zones. Each zone has its own electrically controlled valve. TIP: The valves are powered by 24V AC with a very low current flow and is not normally considered hazardous. This valve is activated by the sprinkler timer or controller. Depending on the installer and the application, some installers place them in a cluster where others place them throughout the yard, or a combination of both. In most cases, (not always) the installer will place the valves in an access can or valve boxes. Unfortunately over time,  these cans (or boxes) can easily disappear under the turf. So if you know where they are,  its good to keep the grass cut back from them or have them marked is some way.

Besides providing an isolation point, sprinkler valves can get dirty or become inoperable. For the most part, the valve can be serviced with replacement parts assuming you know the exact brand and model of the valve.  Read this link on sprinkler valve repair. If the valve is still leaking after a thorough cleaning and inspection, acquire a repair kit and replace all the parts. Rarely would you need to actually remove the valve body from the system unless it became frozen during the winter and the body was cracked. If it was cracked, you should have noticed the valve leaking before you started the dis-assembly process. TIP: Avoiding the cracked valve body is one of the reasons it is recommend to turn off and drain the sprinkler system in the off season.

Finding the valves can be challenging  without the correct tool. Most irrigators have a tool called a cable hound or cable locator. These test sets are about $400-500, so purchasing one is probably out of the question.100_0203 It may be possible to find a rental, but most people that require them usually own them.

Finding zone valves:

  • Cable locator: Professionals use a cable locator to find the valves by tracing the path of the electrical wires that feed each valve. If you have one of these tools or have access to one, this is the simplest and quickest method.  The tone typically get loud when you reach the valve. As an alternative to a Cable Hound, I have tried a low cost test set from Harbor Freight but cannot recommend it as it did not work as I had hoped. It was not really intended for this type of use, but it was worth a shot for the price.  As an alternative, you can hire an irrigator to make the repair and ask him to locate  all the other valves as well. They may not even charge you to find the other valves since they are charging you for the visit and repair. 

So if you are going to try to locate them on your own without a locator, try the following methods:

  1. Design drawing. Hopefully you were left with a drawing from the installer or the previous owner of the property. If  you have any record of who 100_0409installed the system, they may still have one on file.   Find the valves identified on the drawing and use a long screw driver or probe and a shovel to poke around in the dirt. When you hit a valve box it will have a hollow sound to it. They will probably not be in the exact location but hopefully within about 5 feet from where the drawing indicates it.
  2. Origin of Water: The system should have a back flow preventer in a large rectangle box, usually near the water meter.  The sprinkler valve(s) will be located somewhere between the back flow preventer first sprinkler head. Look near the first head of each zone.
  3. Valve Chatter: Assuming you can still turn the system on and off, you can have a friend turn the system on/off multiple time. The valve will make a slapping or hammering noise that may be loud enough to pin point the valve location. 
  4. If you have gone through this without sucess, you may have to call the Irrigator anyway, hopefully using some or all of these methods, you were able to find the valves.100_0411